STPCC0180BTC3 查看數據表（PDF） - STMicroelectronics

零件编号

产品描述 (功能)

生产厂家

STPCC0180BTC3

PC Compatible Embeded Microprocessor

STMicroelectronics 

PIN DESCRIPTION

MD[63:0] Memory Data I/O. This is the 64-bit

memory data bus. If only half of a bank is populat-

ed, MD63-32 is pulled high, data is on MD31-0.

MD[40-0] are read by the device strap option reg-

isters during rising edge of SYSRSTI.

RAS#[3:0] Row Address Strobe Output. There

are 4 active low row address strobe outputs, one

for each bank of the memory. Each bank contains

4 or 8-Bytes of data. The memory controller allows

half of a bank (4-bytes) to be populated to enable

memory upgrade at finer granularity.

The RAS# signals drive the SIMMs directly with-

out any external buffering. These pins are always

outputs, but they can also simultaneously be in-

puts, to allow the memory controller to monitor the

value of the RAS# signals at the pins.

CAS#[7:0] Column Address Strobe Output. There

are 8 active low column address strobe outputs,

one each for each byte of the memory.

The CAS# signals drive the SIMMs either directly

or through external buffers.

These pins are always outputs, but they can also

simultaneously be inputs, to allow the memory

controller to monitor the value of the CAS# signals

at the pins.

MWE# Write Enable Output. Write enable speci-

fies whether the memory access is a read (MWE#

= H) or a write (MWE# = L). This single write ena-

ble controls all the DRAM. It can be externally

buffered to boost the maximum number of loads

(DRAM chips) supported.

The MWE# signals drive the SIMMs directly with-

out any external buffering.

2.2.3 VIDEO INTERFACE

VCLK Pixel Clock Input.

VIN[7:0] YUV Video Data Input CCIR 601 or 656.

Time multiplexed 4:2:2 luminance and chromi-

nance data as defined in ITU-R Rec601-2 and

Rec656 (except for TTL input levels). This bus in-

terfaces with an MPEG video decoder output port

and typically carries a stream of Cb,Y,Cr,Y digital

video at VCLK frequency, clocked on the rising

edge (by default) of VCLK. A 54-Mbit/s ‘double’

Cb, Y, Cr, Y input multiplex is supported for double

encoding application (rising and falling edge of

CKREF are operating).

2.2.4 TV OUTPUT

RED_TV / C_TV Analog video outputs synchro-

nized with CVBS. This output is current-driven and

must be connected to analog ground over a load

resistor (RLOAD). Following the load resistor, a

simple analog low pass filter is recommended. In

S-VHS mode, this is the Chrominance Output.

GREEN_TV / Y_TV Analog video outputs syn-

chronized with CVBS. This output is current-driv-

en and must be connected to analog ground over

a load resistor (RLOAD). Following the load resis-

tor, a simple analog low pass filter is recommend-

ed. In S-VHS mode, this is the Luminance Output.

BLUE_TV / CVBSAnalog video outputs synchro-

nized with CVBS. This output is current-driven and

must be connected to analog ground over a load

resistor (RLOAD). Following the load resistor, a

simple analog low pass filter is recommended. In

S-VHS mode, this is a second composite output.

VCS Line synchronisation Output. This pin is an

input in ODDEV+HSYNC or VSYNC + HSYNC or

VSYNC slave modes and an output in all other

modes (master/slave)

The signal is synchronous to rising edge of CK-

REF. The default polarity uses a negative pulse

ODD_EVEN Frame Synchronisation Ourput. This

pin supports the Frame synchronisation signal. It

is an input in slave modes, except when sync is

extracted from YCrCb data, and an output in mas-

ter mode and when sync is extracted from YCrCb

data

The signal is synchronous to rising edge of DCLK.

The default polarity for this pin is:

- odd (not-top) field : LOW level

- even (bottom) field : HIGH level

IREF1_TV Ref. current for CVBS 10-bit DAC.

VREF1_TV Ref. voltage for CVBS 10-bit DAC.

IREF2_TV Reference current for RGB 9-bit DAC.

VREF2_TV Reference voltage for RGB 9-bit DAC.

VSSA_TV Analog VSS for DAC

VDDA_TV Analog VDD for DAC

CVBS Analog video composite output (luminance/

chrominance). CVBS is current-driven and must

be connected to analog ground over a load resis-

tor (RLOAD). Following the load resistor, a simple

analog low pass filter is recommended.

2.2.5 PCI INTERFACE

AD[31:0] PCI Address/Data. This is the 32-bit

multiplexed address and data bus of the PCI. This

bus is driven by the master during the address

phase and data phase of write transactions. It is

Issue 1.2

15/51

Share Link: