LM350BT 查看數據表（PDF） - Motorola => Freescale
零件编号
产品描述 (功能)
比赛名单
LM350BT Datasheet PDF : 12 Pages
| |||
LM350
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Input–Output Voltage Differential
VI–VO
35
Vdc
Power Dissipation
PD
Internally Limited
W
Operating Junction Temperature Range
TJ
– 40 to +125
°C
Storage Temperature Range
Tstg
– 65 to +150
°C
Soldering Lead Temperature (10 seconds)
Tsolder
300
°C
ELECTRICAL CHARACTERISTICS (VI–VO = 5.0 V; IL = 1.5 A; TJ = Tlow to Thigh; Pmax [Note 1], unless otherwise noted.)
Characteristics
Figure
Symbol
Min
Typ
Max
Unit
Line Regulation (Note 2)
TA = 25°C, 3.0 V ≤ VI–VO ≤ 35 V
Load Regulation (Note 2)
TA = 25°C, 10 mA ≤ Il ≤ 3.0 A
VO ≤ 5.0 V
VO ≥ 5.0 V
Thermal Regulation, Pulse = 20 ms,
(TA = +25°C)
Adjustment Pin Current
Adjustment Pin Current Change
3.0 V ≤ VI–VO ≤ 35 V
10 mA ≤ IL ≤ 3.0 A, PD ≤ Pmax
Reference Voltage
3.0 V ≤ VI–VO ≤ 35 V
10 mA ≤ IO ≤ 3.0 A, PD ≤ Pmax
Line Regulation (Note 2)
3.0 V ≤ VI–VO ≤ 35 V
Load Regulation (Note 2)
10 mA ≤ IL ≤ 3.0 A
VO ≤ 5.0 V
VO ≥ 5.0 V
Temperature Stability (Tlow ≤ TJ ≤ Thigh)
Minimum Load Current to
Maintain Regulation (VI–VO = 35 V)
Maximum Output Current
VI–VO ≤ 10 V, PD ≤ Pmax
VI–VO = 30 V, PD ≤ Pmax, TA = 25°C
RMS Noise, % of VO
TA= 25°C, 10 Hz ≤ f ≤ 10 kHz
Ripple Rejection, VO = 10 V, f = 120 Hz (Note 3)
Without CAdj
CAdj = 10 µF
Long Term Stability, TJ = Thigh (Note 4)
TA= 25°C for Endpoint Measurements
Thermal Resistance, Junction–to–Case
Peak (Note 5)
Average (Note 6)
1
Regline
–
0.0005 0.03
%/V
2
Regload
–
–
Regtherm
–
5.0
25
mV
0.1
0.5
% VO
0.002
–
% VO/W
3
IAdj
–
50
100
µA
1,2
∆IAdj
–
0.2
5.0
µA
3
Vref
1.20 1.25 1.30
V
1
Regline
–
0.02 0.07
%/V
2
Regload
–
20
70
mV
–
0.3
1.5
% VO
3
TS
–
1.0
–
% VO
3
ILmin
–
3.5
10
mA
3
Imax
A
3.0
4.5
–
0.25
1.0
–
N
–
0.003
–
% VO
4
RR
dB
–
65
–
66
80
–
3
S
–
0.3
1.0
%/1.0 k
Hrs.
RθJC
°C/W
–
2.3
–
–
–
1.5
NOTES: 1. Tlow to Thigh = 0° to +125°C; Pmax = 25 W for LM350T; Tlow to Thigh = – 40° to +125°C; Pmax = 25 W for LM350BT
2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately.
Pulse testing with low duty cycle is used.
3. CAdj, when used, is connected between the adjustment pin and ground.
4. Since Long–Term Stability cannot be measured on each device before shipment, this specification is an engineering estimate of average stability
from lot to lot.
5. Thermal Resistance evaluated measuring the hottest temperature on the die using an infrared scanner. This method of evaluation yields very
accurate thermal resistance values which are conservative when compared to the other measurement techniques.
6. The average die temperature is used to derive the value of thermal resistance junction to case (average).
2
MOTOROLA ANALOG IC DEVICE DATA
Share Link: 