MAX2016ETITD 查看數據表（PDF） - Maxim Integrated

零件编号

产品描述 (功能)

比赛名单

MAX2016ETITD

LF-to-2.5GHz Dual Logarithmic Detector/Controller for Power, Gain, and VSWR Measurements

Maxim Integrated 

LF-to-2.5GHz Dual Logarithmic Detector/

Controller for Power, Gain, and VSWR Measurements

ABSOLUTE MAXIMUM RATINGS

VCC to GND .........................................................-0.3V to +5.25V

Input Power Differential (RFIN_+, RFIN_-)......................+23dBm

Input Power Single Ended (RFIN_+ or RFIN _-) .............+19dBm

All Other Pins to GND.................................-0.3V to (VCC + 0.3V)

Continuous Power Dissipation (TA = +70°C)

28-Pin, 5mm x 5mm Thin QFN (derate 35.7mW/°C

above +70°C)..................................................................2.8W

Operating Temperature Range ...........................-40°C to +85°C

Junction Temperature ......................................................+150°C

Storage Temperature Range .............................-65°C to +150°C

Lead Temperature (soldering, 10s) .................................+300°C

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

DC ELECTRICAL CHARACTERISTICS

(VCC = +2.7V to +3.6V, R1 = R2 = R3 = 0Ω, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = +3.3V,

CSETL = CSETH = VCC, 50Ω RF system, TA = +25°C, unless otherwise noted.) (Note 1)

PARAMETER

POWER SUPPLY

Supply Voltage

Total Supply Current

Supply Current

INPUT INTERFACE

Input Impedance

Input Resistance

DETECTOR OUTPUT

Source Current

Sink Current

Minimum Output Voltage

Maximum Output Voltage

Difference Output VOUTD

OUTD Accuracy

COMPARATORS

Output High Voltage

Output Low Voltage

Input Voltage

Input Bias Current

REFERENCE

Output Voltage on Pin 25

Load Regulation

SYMBOL

CONDITIONS

MIN TYP MAX UNITS

VS

R6 = 0Ω

VS

R6 = 37.4Ω

ICC

Measured in each pin 2 and pin 20

Measured in pin 9

Measured in pin 12

2.7

3.3

3.6

V

4.75

5

5.25

43

55

mA

16

2

mA

9

Differential impedance at RFINA and RFINB

50

Ω

Resistance at SETD

R

Resistance at SETA and SETB

20

kΩ

40

Measured at OUTA, OUTB, and OUTD

Measured at OUTA, OUTB, and OUTD

Measured at OUTA, OUTB, and OUTD

Measured at OUTA, OUTB, and OUTD

PRFINA = PRFINB = -30dBm

4

mA

0.45

mA

0.5

V

1.8

V

1

V

±12

mV

VOH

VOL

RLOAD ≥ 10kΩ

RLOAD ≥ 10kΩ

Measured at CSETL and CSETH

CSETL and CSETH

RLOAD ≥ 2kΩ

Source 2mA

VCC -

V

10mV

10

mV

GND to

V

VCC

1

nA

2

V

-5

mV

2 _______________________________________________________________________________________

Share Link: