MAX4501CPA 查看數據表（PDF） - Maxim Integrated
零件编号
产品描述 (功能)
比赛名单
MAX4501CPA Datasheet PDF : 8 Pages
| |||
Low-Voltage, SPST, CMOS Analog Switches
ABSOLUTE MAXIMUM RATINGS
(Voltages Referenced to GND)
V+ ...........................................................................-0.3V to +13V
Voltage into Any Terminal (Note 1) ..........-0.3V to (V+ + 0.3V) or
±10mA (whichever occurs first)
Continuous Current into Any Terminal..............................±10mA
Peak Current, NO or COM
(pulsed at 1ms, 10% duty cycle)..................................±20mA
ESD per Method 3015.7 ..................................................>2000V
Continuous Power Dissipation (TA = +70°C)
5-Pin SC70-5 (derate 2.5mW/°C above +70°C)...........200mW
5-Pin SOT23-5 (derate 7.1mW/°C above +70°C) ........571mW
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ...727mW
8-Pin CERDIP (derate 8.00mW/°C above +70°C)........640mW
Operating Temperature Ranges
MAX4501C_ _/MAX4502C_ _ .............................0°C to +70°C
MAX4501E_ _/MAX4502E_ _ ...........................-40°C to +85°C
MAX4501MJA/MAX4502MJA ........................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: Voltages exceeding V+ or GND on any signal terminal are clamped by internal diodes. Limit forward-diode current to
maximum current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—+5V Supply
(V+ = +4.5V to +5.5V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
ANALOG SWITCH
Analog Signal Range
VCOM,
VNO, VNC
0
V+
V
COM to NO or NC
On-Resistance
NO or NC Off-Leakage Current
(Notes 3, 4)
RON
VCOM = 3.5V,
ICOM = 1mA
INO(OFF),
INC(OFF)
V+ = 5.5V,
VCOM = 1V,
VNO or VNC = 4.5V
TA = +25°C
TA = TMIN to TMAX
TA = +25°C
TA = TMIN C, E
to TMAX M
90
250
Ω
350
-1
0.01
1
-10
10
nA
-100
100
COM Off-Leakage Current
(Notes 3, 4)
V+ = 5.5V,
ICOM(OFF) VCOM = 1V,
VNO or VNC = 4.5V
TA = +25°C
TA = TMIN C, E
to TMAX M
-1
0.01
1
-10
10
nA
-100
100
COM On-Leakage Current
(Notes 3, 4)
ICOM(ON)
V+ = 5.5V,
VCOM = 1V, 4.5V
TA = +25°C
TA = TMIN C, E
to TMAX M
-2
0.01
2
-20
20
nA
-200
200
DIGITAL I/O
Input Logic High
VINH
Input Logic Low
VINL
Input Current Logic High or Low IINH, IINL
SWITCH DYNAMIC CHARACTERISTICS
VIN = V+, 0
2.4
V+
V
0
0.8
V
-1
0.03
1
µA
Turn-On Time
VNO = VNC = 1.5V,
TA = +25°C
tON
VIN = 3V, RL = 1kΩ,
CL = 35pF, Figure 1 TA = TMIN to TMAX
16
75
ns
150
Turn-Off Time
VNO = VNC = 1.5V,
TA = +25°C
tOFF VIN = 3V, RL = 1kΩ,
CL = 35pF, Figure 1 TA = TMIN to TMAX
10
50
ns
150
2 _______________________________________________________________________________________
Share Link: 