FBL2041 查看數據表（PDF） - Philips Electronics
零件编号
产品描述 (功能)
比赛名单
FBL2041 Datasheet PDF : 12 Pages
| |||
Philips Semiconductors
3.3V BTL 7-bit Futurebus+ transceiver (standard A-port)
Product specification
FBL2041
FBL2041I
DC ELECTRICAL CHARACTERISTICS
Over recommended operating free-air temperature range unless otherwise noted.
SYMBOL
PARAMETER
TEST CONDITIONS1
LIMITS
MIN
TYP2
UNIT
MAX
IOH High level output current B0 – B6
VCC = MAX, VIL = MAX, VOH = 1.9V
100
µA
IOFF Power-off output current B0 – B6
VCC = 0V, VIL = MAX, VOH = 1.9V
VCC = 0V, VIL = MAX, VOH = 1.9V @ 85°C
100
µA
300
µA
VCC = MIN to MAX; IOH = -100µA
VCC –0.2
V
VOH
High-level output
voltage
AO0 – AO63
VCC = MIN; IOH = -8mA
2.4
V
VCC = MIN; IOH = -32mA
2.0
V
AO0 – AO63
VOL Low-level output voltage
VCC = MIN; IOL = 16mA
VCC = MIN; IOL = 32mA
0.4
V
0.5
V
B0 – B6
VCC = MIN, IOL = 4mA
VCC = MIN, IOL = 100mA
0.5
V
0.75
1.0
1.20
VIK
Input clamp voltage
VCC = MIN, II = IIK = –18mA
–0.85 -1.2
V
Control pins
VCC = 3.6V; VI = VCC or GND
±1.0
II
Input leakage current
Control/ AI0 – AI6
AI0 – AI6
VCC = 0V or 3.6V; VI = 5.5V
VCC = 3.6V; VI = VCC
10
µA
1
Note 4
VCC = 3.6V; VI = 0V
–5
VCC = MAX, VI = 1.9V
100
µA
IIH
High-level input current B0 – B6
VCC = MAX, VI = 3.5V, note 5
100
mA
VCC = MAX; VI = 3.75V @ –40°C
100
mA
IIL
Low-level input current B0 – B6
VCC = MAX, VI = 0.75V
-100 µA
IOZH Off-state output current AO0 – AO6
VCC = MAX, VO =3V
5
µA
IOZL Off-state output current AO0 – AO6
VCC = MAX, VO = 0.5V
-5
µA
ICCZ
VCC = MAX
5.2
13.5
ICC Supply current (total)
ICCB
ICCL
VCC = MAX, outputs Low or High
VCC = MAX, outputs Low
3.2
9.0
mA
13.5
19.5
ICCH
VCC = MAX, outputs High
10.7
16.0
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operation conditions for the applicable type.
2. All typical values are at VCC = 3.3V, TA = 25°C.
3. Due to test equipment limitations, actual test conditions are VIH = 1.8V and VIL = 1.3V for the B side.
4. Unused pins are at VCC or GND.
5. For B port input voltage between 3 and 5 volt; IIH will be greater than 100mA but the part will continue to function normally (clamping circuit
is active).
1999 Apr 27
7
Share Link: 