MT88E45 查看數據表（PDF） - Zarlink Semiconductor Inc

零件编号

产品描述 (功能)

比赛名单

MT88E45

4-Wire Calling Number Identification Circuit 2 (4-Wire CNIC2)

Zarlink Semiconductor Inc 

MT88E45

Data Sheet

2130 Hz and 2750 Hz

CAS/DT-AS Characteristics

Bellcorea

(Off-hook only)

ETSIb

(Off-hook)

BTc

(Off-hook = ‘Loop State’)

(On-hook = ‘Idle State’)

Duration

Reject Duration

Signal to Noise Ratio

Hybrid Op-amp (GS2) Gain

Vdd = 5V +/- 10%

Hybrid Op-amp (GS2) Gain

Vdd = 3V +/- 10%

75 to 85 ms

Speech

0 to -5 dB

-3.5 to -8.5 dB

75 to 85 ms

Speech

0 to -5 dB

-3.5 to -8.5 dB

Off-hook: 80 to 85 ms

On-hook: 88 to 110 ms

Off-hook: <=70 ms

On-hook: <=20 ms

Off-hook: Speech

On-hook: >= 20 dB

(300-3400 Hz)

0 dB

-3.5 dB

a. SR-TSV-002476, Issue 1 Dec 1992

b. ETS 300 778-2 Jan 98. The DT-AS plus FSK variant of ETSI on-hook signalling described in ETS 300 778-1 is not supported

because on-hook DT-AS uses the GS1 op-amp. With the GS1 gain in Table 4, the DT-AS minimum level will be below the

MT88E45B’s minimum accept level.

c. SIN227 Issue 3 Nov 97, SIN242 Issue 2 Nov 96

d. dBm - Decibels above or below a reference power of 1 mW into 600 ohms. 0 dBm = 0.7746 Vrms.

e. dBV - Decibels above or below a reference voltage of 1 Vrms. 0 dBV = 1 Vrms

Table 3 - CAS/DT-AS Characteristics

Table 3 shows the Hybrid op-amp (GS2) gain for operation at 3 V and 5 V nominal Vdd, with a ± 10% Vdd variation.

For 3 V operation, the Hybrid op-amp gain should be reduced from the 5 V setting to maintain the CAS reject level

and to maintain the talkoff immunity: the CAS threshold is directly proportional to Vdd, when Vdd is reduced the

threshold becomes lower, hence lower level CAS are accepted. If the gain is not reduced, the MT88E45B will be

more talkoff prone. In Table 3, the GS2 gain is shown as a range. By adopting the lower gain, talkoff immunity can

be improved.

When CAS detection is selected, the dual purpose output pin DR/STD is STD. STD goes low when CAS has been

detected, and returns high after CAS has ended.

CAS Guard Time

The guard time circuit shown in Figure 55 implements a timing algorithm which determines whether the signal is a

CAS. Proper selection of the guard time(s) is key to good speech immunity. The first indication that there might be a

CAS is when EST goes high. EST high indicates that both tones are present. EST low indicates that one or both

tones is not present. STD low indicates that CAS has been detected. When STD returns high it indicates that CAS

has ended.

The timing algorithm consists of 2 components: a tone present guard time (tGP) and a tone absent guard time (tGA).

tGP sets the minimum accept duration for CAS. That is, both tones must be detected continuously for tGP for STD to

go low to indicate that CAS has been detected. For STD to return high to indicate that CAS has ended, one or both

tones must have disappeared for tGA. The purpose of tGA is to bridge over momentary EST dropouts once EST has

met the minimum tone duration so as to decrease the likelihood of a long talkoff being broken up into several

talkoffs. Usually tGA is set very short or removed altogether because there is another way to deal with the problem

(by ignoring further detections for 2 seconds after every detection).

9

Zarlink Semiconductor Inc.

Share Link: