NCP1070, NCP1071, NCP1072, NCP1075, NCP1076, NCP1077
ELECTRICAL CHARACTERISTICS
(For all NCP107X products except NCP1072P100BG: For typical values TJ = 25°C, for min/max values TJ = −40°C to +125°C, VCC = 8 V
unless otherwise noted)
(For NCP1072P100BG: For typical values TJ = 25°C, for min/max values TJ = −55°C (Note 7) to +125°C, VCC = 8 V unless otherwise noted)
Symbol
Rating
Pin
Min
Typ
Max
Unit
CURRENT COMPARATOR
IIPK(0)
Maximum internal current setpoint at beginning of switching cycle
FB pin open, Tj = 25°C
NCP1070
NCP1071
NCP1072
NCP1075
NCP1076
NCP1077
mA
273
304
334
382
425
467
254
282
310
467
508
549
689
765
841
846
940 1034
IIPKSW
IIPKSW
Final switch current with a primary slope of 200 mA/ms,
FSW =65 kHz (Note 4)
NCP1070
NCP1071
NCP1072
NCP1075
NCP1076
NCP1077
Final switch current with a primary slope of 200 mA/ms,
FSW =100 kHz (Note 4)
NCP1070
NCP1071
NCP1072
NCP1075
NCP1076
NCP1077
mA
−
314
−
−
427
−
−
296
−
−
510
−
−
732
−
−
881
−
mA
−
309
−
−
415
−
−
293
−
−
500
−
−
706
−
−
845
−
IIPKSW
Final switch current with a primary slope of 200 mA/ms,
FSW =130 kHz
NCP1070
NCP1071
NCP1072 (Note 5)
NCP1075
NCP1076
NCP1077
mA
−
303
−
−
407
−
−
291
−
−
493
−
−
684
−
−
814
−
TSS
Soft−start duration (guaranteed by design)
TLEB
Leading Edge Blanking Duration
Tprop
Propagation delay from current detection to drain OFF state
INTERNAL OSCILLATOR
−
−
1
−
ms
−
−
200
−
ns
−
−
100
−
ns
fOSC
fOSC
fOSC
fjitter
fswing
Dmax
Oscillation frequency, 65 kHz version, Tj = 25°C (Note 6)
Oscillation frequency, 100 kHz version, Tj = 25°C (Note 6)
Oscillation frequency, 130 kHz version, Tj = 25°C (Note 5 et 6)
Frequency jittering in percentage of fOSC
Jittering swing frequency
Maximum duty−cycle
NCP1070/71/72/75 except NCP1072P100BG
NCP1076/77/72B & NCP1072P100BG
−
59
65
71
kHz
−
90
100
110
kHz
−
117
130
143
kHz
−
−
±6
−
%
−
−
300
−
Hz
%
−
62
68
72
−
65
69
73
FEEDBACK SECTION
IFBfault FB current for which Fault is detected
4
−35
mA
IFB100% FB current for which internal current set−point is 100% (IIPK(0))
4
−44
mA
IFBFreeze FB current for which internal current set−point is IFreeze
4
−
−90
−
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
4. The final switch current is: IIPK(0) / (Vin/LP + Sa) x Vin/LP + Vin/LP x tprop, with Sa the built−in slope compensation, Vin the input voltage, LP
the primary inductor in a flyback, and tprop the propagation delay.
5. NCP1072 130 kHz on demand only.
6. Oscillator frequency is measured with disabled jittering.
7. For coldest temperature, QA sampling at −40°C in production and −55°C specification is Guaranteed by Characterization.
www.onsemi.com
6