HIP4080 查看數據表（PDF） - Intersil
零件编号
产品描述 (功能)
比赛名单
HIP4080 Datasheet PDF : 21 Pages
| |||
HIP4080
Absolute Maximum Ratings
Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . . . -0.3V to 16V
Logic I/O Voltages . . .
Voltage on AHS, BHS
.
.
.
.
.
.
.....
-6.0V
.........
(Transient)
..
to
.80-0V.3(2V5tooCVtDoD12+50o.3CV)
Voltage on AHS, BHS . . . -6.0V (Transient) to 70V (-55oC to 125oC
Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient)
Voltage on AHB, BHBVAHS, BHS -0.3V to VAHS, BHS +16VVoltage on
Voltage on ALO, BLO. . . . . . . . . . . . . VALS, BLS -0.3V to VCC +0.3V
Voltage on AHO, BHO . . . . . . VAHS, BHS -0.3V to VAHB, BHB +0.3V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns
All Voltages relative to pin 4, VSS, unless otherwise specified.
Operating Conditions
Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . . . +8V to +15V
Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V
Voltage on AHB, BHB . . . . . . . . VAHS, BHS +5V to VAHS, BHS +15V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . -500µA to -50µA
Operating Ambient Temperature Range . . . . . . . . . . -40oC to 85oC
Thermal Information
Thermal Resistance (Typical, Note 1) . . . . . . . . . . . . . . . θJA (oC/W)
SOIC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Maximum Power Dissipation at 85oC
SOIC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470mW
DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530mW
Storage Temperature Range. . . . . . . . . . . . . . . . . . -65oC to 150oC
Operating Max. Junction Temperature . . . . . . . . . . . . . . . . . . 125oC
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
PARAMETERS
VDD
TA =
2=5VoCCC, U=nVleAsHsBO=thVeBrwHiBse=S1p2eVc, iVfieSdS
=
VALS
=
VBLS
=
VAHS
=
VBHS
=
0V,
RHDEL
=
RLDEL
=
100K,
and
TJ = 25oC
TTJO=1-2450ooCC
SYMBOL
TEST CONDITIONS
MIN TYP MAX MIN MAX UNITS
SUPPLY CURRENTS AND CHARGE PUMPS
VDD Quiescent Current
IDD
IN- = 2.5V, Other Inputs = 0V
VDD Operating Current
IDDO Outputs switching f = 500kHz
VCC Quiescent Current
ICC
IN- = 2.5V, Other Inputs = 0V,
IALO = IBLO = 0
VCC Operating Current
ICCO f = 500kHz, No Load
AHB, BHB Quiescent Current -
Qpump Output Current
IAHB, IBHB
IN- = 2.5V, Other Inputs = 0V, IAHO =
IBHO = 0, VDD = VCC = VAHB =
VBHB = 10V
AHB, BHB Operating Current
IAHBO,
IBHBO
f = 500kHz, No Load
AHS, BHS, AHB, BHB Leakage Current
IHLK
VAHS = VBHS = VAHB = VBHB = 95V
AHB-AHS, BHB-BHS Qpump
Output Voltage
VAHB -
VAHS
VBHB -
VBHS
IAHB = IAHB = 0, No Load
INPUT COMPARATOR PINS: IN+, IN-, OUT
8 10.5 13
9
11 14
-
25 80
7
14 mA
8
15 mA
- 100 µA
1
1.5 2.0 0.8
3
mA
-50 -30 -15 -60 -10 µA
0.5 0.9 1.3 0.4 1.7 mA
- 0.02 1.0
-
10 µA
11.5 12.6 14.0 10.5 14.5 V
Offset Voltage
Input Bias Current
Input Offset Current
Input Common Mode Voltage Range
VOS
IIB
IOS
CMVR
Over Common Mode Voltage Range
-10 0 +10 -15 +15 mV
0
0.5
2
0
4
µA
-1
0
+1 -2 +2 µA
1
-
VDD
1
VDD
V
-1.5
-1.5
Voltage Gain
AVOL
10 25
-
10
- V/mV
4
Share Link: 