TC115(2003) 查看數據表（PDF） - Microchip Technology

零件编号

产品描述 (功能)

比赛名单

TC115
(Rev.:2003)

PFM/PWM Step-Up DC/DC Converter

Microchip Technology 

TC115

Rewriting in terms of input and output currents and volt-

ages:

EQUATION 5-5:

( VINMIN )( IINMAX )

=

-(--V----O----U---T---M---A--X---)--(--I---O----U---T---M---A--X---)

Efficiency

Solving for input current:

EQUATION 5-6:

II NMA X

=

-(---V----O---U----T---M---A--X---)--(--I---O----U---T---M---A--X---)-

(Efficiency)(VINMIN )

The sawtooth current is centered on the DC current

level, swinging equally above and below the DC current

calculated in Equation 5-6. The peak inductor current is

the sum of the DC current plus half the ac current. Note

that minimum input voltage should be used when

calculating the ac inductor current (Equation 5-9).

EQUATION 5-7:

VL = L(di ⁄ dt)

EQUATION 5-8:

di = VL(di ⁄ dt)

EQUATION 5-9:

di = -(--V----I--N---M---I--N---–-----V----S--W----)---t--O---N--

L

Where:

VSW = The voltage drop across the internal

N-channel MOSFET.

Combining the DC current calculated in Equation 5-6,

with half the peak ac current calculated in Equation 5-9,

the peak inductor current is given by:

EQUATION 5-10:

IPK = IINMAX + 0.5(di)

5.3 Internal Transistor Switch

The LX pin has a typical ON resistance of 1.4Ω.

Therefore, peak switch current is given by (VIN/1.4).

The internal transistor switch has a maximum design

rating of 350 mA. An oscillator frequency doubling cir-

cuit is an included guard against high switching cur-

rents. Should the voltage on the LX pin rise above 1.3V

(max) while the internal N-channel switch is ON, the

oscillator frequency automatically doubles to minimize

ON time. Although reduced, switch current still flows

because the PWM remains in operation. Therefore, the

LX input is not internally current-limited and care must

be taken never to exceed the 350 mA maximum limit.

Failure to observe this will result in damage to the

regulator.

5.4 Output Capacitor

The effective series resistance of the output capacitor

directly affects the amplitude of the output voltage

ripple (The product of the peak inductor current and the

ESR determines output ripple amplitude). Therefore, a

capacitor with the lowest possible ESR should be

selected. Smaller capacitors are acceptable for light

loads (or in applications where ripple is not a concern).

The Sprague® 595D series of tantalum capacitors are

among the smallest of all low ESR surface mount

capacitors available. Table 5-1 lists suggested

components and suppliers.

5.5 Board Layout Guidelines

As with all inductive switching regulators, the TC115

generates fast switching waveforms which radiate

noise. Interconnecting lead lengths should be

minimized to keep stray capacitance, trace resistance

and radiated noise as low as possible. In addition, the

GND pin, input bypass capacitor and output filter

capacitor ground leads should be connected to a single

point.

TABLE 5-1: SUGGESTED COMPONENTS AND SUPPLIERS

Type

Surface Mount

Through-Hole

Inductors

Sumida®

CD54 Series

CDR125 Series

Coiltronics™

CTX Series

Sumida®

RCH855 Series

RCH110 Series

Renco®

RL1284-12

Capacitors

Matsuo®

267 Series

Sprague®

595D Series

Nichicon™

F93 Series

Sanyo™

OS-CON Series

Nichicon™

PL Series

Diodes

Nihon

EC10 Series

Matsushita™

MA735 Series

ON Semiconductor®

1N5817 - 1N5822

 2003 Microchip Technology Inc.

DS21361C-page 7

Share Link: