LTC1647-3 查看數據表（PDF） - Linear Technology

零件编号

产品描述 (功能)

比赛名单

LTC1647-3

Dual Hot Swap Controllers

Linear Technology 

LTC1647-1/LTC1647-2/LTC1647-3

PI FU CTIO S

VCC1 (LTC1647-3): Channel 1 Positive Supply Input. The

supply range for normal operation is 2.7V to 16.5V. The

supply current, ICC1, is typically 1mA. Channel 1’s under-

voltage lockout (UVLO) circuit disables GATE 1 until the

supply voltage at VCC1 is greater than VLKO (typically

2.47V). GATE 1 is held at ground potential until UVLO

deactivates. If ON1 is high and VCC1 is above the UVLO

threshold voltage, GATE 1 is pulled high by a 10µA current

source. If VCC1 falls below (VLKO – VLKH), GATE 1 is pulled

immediately to ground. The internal reference and the

common charge pump are powered from the higher of the

two VCC inputs, VCC1 or VCC2.

VCC2 (LTC1647-3): Channel 2 Positive Supply Input. See

VCC1 for functional description.

VCC: The Common Positive Supply Input for the LTC1647-1

and the LTC1647-2. VCC1 and VCC2 are internally con-

nected together.

GND: Chip Ground.

ON1: Channel 1 ON Input. The threshold at the ON1 pin is

set at 1.28V with 70mV hysteresis. If UVLO and the circuit

breaker of channel 1 are inactive, a logic high at ON1

enables the 10µA charge pump current source, pulling the

GATE 1 pin above VCC1. If the ON1 pin is pulled low, the

GATE 1 pin is pulled to ground by a 50µA current sink.

ON1 resets channel 1’s electronic circuit breaker by pull-

ing ON1 low for greater than one tRESET period (50µs). A

low-to-high transition at ON1 restarts a normal GATE 1

pull-up sequence.

ON2: Channel 2 ON Input. See ON1 for functional descrip-

tion.

FAULT 1: Channel 1 Open-Drain Fault Status Output.

FAULT 1 pin pulls low after 0.3µs (tFAULT) if the circuit

breaker measures greater than 50mV across the sense

resistor connected between VCC1 and SENSE 1. If FAULT 1

pulls low, GATE 1 also pulls low. FAULT 1 remains low until

ON1 is pulled low for at least one tRESET period.

FAULT 2: Channel 2 Open-Drain Fault Status Output. See

FAULT 1 for functional description.

SENSE 1: Channel 1 Circuit Breaker Current Sense Input.

Load current is monitored by a sense resistor connected

between VCC1 and SENSE 1. The circuit breaker trips if the

voltage across the sense resistor exceeds 50mV (VCB). To

disable the circuit breaker, connect SENSE 1 to VCC1. In

order to obtain optimum performance, use Kelvin-sense

connections between the VCC and SENSE pins to the

current sense resistor.

SENSE 2: Channel 2 Circuit Breaker Current Sense Input.

See SENSE 1 for functional description.

GATE 1: Channel 1 N-Channel MOSFET Gate Drive Output.

An internal charge pump guarantees at least 10V of gate

drive from a 5V supply. Two Zener clamps are incorpo-

rated at the GATE 1 pin; one Zener clamps GATE 1

approximately 15V above VCC and the second Zener

clamps GATE 1 appoximately 28V above GND. The rise

time at GATE 1 is set by an external capacitor connected

between GATE 1 and GND and an internal 10µA current

source provided by the charge pump. The fall time at GATE

1 is set by the 50µA current sink if ON1 is pulled low. If the

circuit breaker is tripped or the supply voltage hits the

UVLO threshold, a 50mA current sink rapidly pulls GATE 1

low.

GATE 2: Channel 2 N-Channel MOSFET Gate Drive Output.

See GATE 1 for functional description.

NC: No Connection.

7

Share Link: