MU9C8358 查看數據表（PDF） - MUSIC Semiconductors

零件编号

产品描述 (功能)

比赛名单

MU9C8358

Quad 10/100Mb Ethernet Filter Interface

MUSIC Semiconductors 

08& 4XDG 0E (WKHUQHW )LOWHU ,QWHUID.H

3LQ 'HV.ULSWLRQV

5HVXOW 3RUW ,QWHUID.H

See Timing Diagrams: Timing Data for Result Port

Interface and Table 1 for the Result Port bit descriptions.

&RQWURO ,QWHUID.HV

(See Timing Diagrams: Timing Data for Control

Interfaces).

Note: Although the result data register also can be read through

the processor port, it is important to note that the means of

retrieving the data must be unique. Therefore, if the user is not

using the Result Port Interface, but is reading result data through

the processor port, RP_NXT and RP_SEL should be pulled low.

This ensures that all result data remains in the Result Data

register until read through the processor port. RP_NXT and

RP_SEL should be pulled low to 0 volts through a pull-down

resistor (typically 10k ohms).

53>@ 5HVXOW 3RUW 'DWD 2XWSXW 7ULVWDWH 77/

The Result Port Data carries the results of recently

processed packets detected on the MII ports. See Table 1

for details of the Result Port Data bit descriptions. These

are identical to the Result Data register bits.

53B'9 5HVXOW 3RUW 'DWD 9DOLG 2XWSXW 77/

The Result Port Data Valid indicates that the RP port

carries valid packet data. As long as there is valid packet

data, RP_DV will stay HIGH.

53B1;7 5HVXOW 3RUW 1H[W 'DWD ,QSXW 77/

The Result Port Next pin brings the next result to the RP

bus if RP_SEL is asserted. If there are no additional results

available, the RP_DV will drop LOW after the time

interval specified in the Result Port Timing specification.

53B6(/ 5HVXOW 3RUW 6HOH.W ,QSXW 77/

The Result Port Select pin controls RP[15:0] and

RP_NXT. RP_NXT and RP_SEL are connected by a

logical AND. Therefore, RP_SEL must be HIGH in order

for RP_NXT to bring the next result to the RP bus. RP and

RP_NXT from two MU9C8358 components (eight ports)

can be wired together on a common bus in order to run

these components in cascade. Refer to Figure 3. RP_SEL

can stay continuously HIGH if one MU9C8358 is being

implemented. As long as there is valid packet data,

RP_DV will stay HIGH.

6<6&/. 6\VWHP &OR.N ,QSXW 77/

CLK is the user-supplied system clock for synchronous

chip operation; its frequency must be 50 MHz with duty

cycle between 45 to 55 percent.

5(6(7 5HVHW ,QSXW 77/

When system Reset is taken LOW, all internal

state-machines are reset to their initial state and any data is

cleared. All registers are returned to default values.

/RESET is synchronous and should be held LOW for a

minimum of two SYSCLK cycles. The user must set the

LANCAM Segment Control register after asserting

/RESET.

,1&5 ,Q.UHPHQW 7LPH 6WDPS &RXQWHUV ,QSXW 77/

INCR is a user command to invoke the built-in purge

routine. Both STCURR and STPURG 8-bit counters are

advanced one count on the rising edge of INCR, and the

time stamp stored with each LANCAM entry is compared

with STPURG. Matching entries subsequently are purged

or deleted. This pin must be configured, if it is required, by

setting bit 2 and bit 3 in the System Target (STARG)

register. Each counter can be incremented individually

through the Processor Port. (see Operational

Characteristics: STARG System Target Register

Mapping).

7DEOH  5HVXOW 3RUW %LW 'HV.ULSWLRQV

%LW V











'HV.ULSWLRQ

%LW 6RXU.H 3RUW ,'

3D.NHW 7\SH %URDG.DVW  0XOWL.DVW  8QL.DVW 

LI 8QL.DVW 0DW.K )RXQG

%LW LI &$0 0DW.K )RXQG 'HVWLQDWLRQ 3RUW ,'

,I 0DW.K )RXQG 'HVWLQDWLRQ 3RUW 6RXU.H 3RUW



5HY  'UDIW

Share Link: