IDT7024S15PF 查看數據表（PDF） - Integrated Device Technology

零件编号

产品描述 (功能)

比赛名单

IDT7024S15PF

HIGH-SPEED 4K x 16 DUAL-PORT STATIC RAM

Integrated Device Technology 

IDT7024S/L

HIGH-SPEED 4K x 16 DUAL-PORT STATIC RAM

MILITARY AND COMMERCIAL TEMPERATURE RANGES

AC ELECTRICAL CHARACTERISTICS OVER THE

OPERATING TEMPERATURE AND SUPPLY VOLTAGE(5)

Symbol

Parameter

IDT7024X15

Com'l. Only

Min. Max.

IDT7024X17

Com'l. Only

Min. Max.

WRITE CYCLE

tWC

Write Cycle Time

tEW

Chip Enable to End-of-Write(3)

15

—

17

—

12

—

12

—

tAW

Address Valid to End-of-Write

tAS

Address Set-up Time(3)

12

—

12

—

0

—

0

—

tWP

Write Pulse Width

12

—

12

—

tWR

Write Recovery Time

0

—

0

—

tDW

Data Valid to End-of-Write

10

—

10

—

tHZ

Output High-Z Time(1, 2)

—

10

—

10

tDH

Data Hold Time(4)

0

—

0

—

tWZ

Write Enable to Output in High-Z(1, 2)

—

10

—

10

tOW

Output Active from End-of-Write(1, 2, 4)

0

—

0

—

tSWRD

SEM Flag Write to Read Time

5

—

5

—

tSPS

SEM Flag Contention Window

5

—

5

—

IDT7024X20

Min. Max.

20

—

15

—

15

—

0

—

15

—

0

—

15

—

—

12

0

—

—

12

0

—

5

—

5

—

IDT7024X25

Min. Max. Unit

25

— ns

20

— ns

20

— ns

0

— ns

20

— ns

0

— ns

15

— ns

—

15 ns

0

— ns

—

15 ns

0

— ns

5

— ns

5

— ns

Symbol

Parameter

IDT7024X35

Min. Max.

IDT7024X55

Min. Max.

IDT7024X70

Mil. Only

Min. Max. Unit

WRITE CYCLE

tWC

Write Cycle Time

tEW

Chip Enable to End-of-Write(3)

35

—

55

—

70

— ns

30

—

45

—

50

— ns

tAW

Address Valid to End-of-Write

tAS

Address Set-up Time(3)

30

—

45

—

50

— ns

0

—

0

—

0

— ns

tWP

Write Pulse Width

25

—

40

—

50

— ns

tWR

Write Recovery Time

0

—

0

—

0

— ns

tDW

tHZ

tDH

tWZ

tOW

tSWRD

tSPS

Data Valid to End-of-Write

Output High-Z Time(1, 2)

Data Hold Time(4)

Write Enable to Output in High-Z(1, 2)

Output Active from End-of-Write(1, 2, 4)

SEM Flag Write to Read Time

SEM Flag Contention Window

15

—

30

—

40

— ns

—

15

—

25

—

30 ns

0

—

0

—

0

— ns

—

15

—

25

—

30 ns

0

—

0

—

0

— ns

5

—

5

—

5

— ns

5

—

5

—

5

— ns

NOTES:

2740 tbl 14

1. Transition is measured ±500mV from Low or High-impedance voltage with the Output Test Load (Figure 2).

2. This parameter is guaranteed by device characterization, but is not production tested.

3. To access RAM, CE = VIL, UB or LB = VIL, SEM = VIH. To access semaphore, CE = VIH or UB & LB = VIH, and SEM = VIL. Either condition must be valid

for the entire tEW time.

4. The specification for tDH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary

over voltage and temperature, the actual tDH will always be smaller than the actual tOW.

5. "X" in part numbers indicates power rating (S or L).

6.15

9

Share Link: