MAX5005_CUB 查看數據表（PDF） - Maxim Integrated
零件编号
产品描述 (功能)
比赛名单
MAX5005_CUB Datasheet PDF : 13 Pages
| |||
150mA USB LDO Regulators with ±15kV TVS
and µP Reset
ELECTRICAL CHARACTERISTICS (continued)
(VIN = +5V, IOUT = 0, COUT = 2.2µF, TA = 0°C to +70°C, unless otherwise noted. Typical specifications are at TA = +25°C.) (Note 1)
PARAMETER
SELR Input Current
SYMBOL
CONDITIONS
SELR = GND or OUT
ENR Input Voltage
VIL
RTERM enabled
VIH
RTERM disabled
ENR Input Current
Open-Drain RESET Output Low
Voltage (MAX5005)
Open-Drain Reset Output Leakage
Current (MAX5005)
VOL
ILKG
ENR = GND or OUT
VOUT > 1.0V, ISINK = 50µA, reset asserted
VOUT > 2.7V, ISINK = 3.2mA, reset asserted
Reset not asserted
Push-Pull RESET Output Voltage
(MAX5006)
VOUT = 1.0V, ISINK = 50µA, reset asserted
VOL VOUT > VTH(MIN), ISINK = 3.2mA, reset
asserted
VOH
VOUT > VTH(MAX), ISOURCE = 500µA,
reset not asserted
Push-Pull RESET Output Voltage
(MAX5007)
VOL
VOH
VOUT > VTH(MAX), ISINK = 3.2mA,
reset not asserted
VOUT = 1.0V, ISOURCE = 150µA, reset
asserted
USB OPTIONS AND TRANSIENT SUPPRESSION
D+/D- RTERM Impedance
ENR = GND, SELR = GND or OUT
D+/D- Input Leakage Current
D+ to D- Capacitance
VENR = VOUT = 3.3V
1MHz, 100mVp-p signal
applied at D+ and D-,
VOUT = 3.3V
ENR = OUT
Unpowered
D+, D- Capacitance to GND
ESD Trigger Voltage
Surge Trigger Voltage
Clamping Voltage
1MHz, 100mVp-p signal
applied at D+ and D-,
VOUT = 3.3V
ENR = OUT
Unpowered
dV/dt < 1V/ns, VD+ or VD- > 3.6V
dV/dt < 2V/µs, VD+ or VD- > 3.6V
6A, pulse width = 200ns to 40µs
Surge Current
16V, pulse width = 200ns to 40µs
Human Body Model MIL-STD-883
D+/D- to GND ESD
Contact Discharge IEC1000-4-2
(EN61000-4-2)
Air Discharge IEC1000-4-2 (EN61000-4-2)
MIN
-1
0.8 x
VOUT
-1
-1.0
0.8 x
VOUT
0.8 x
VOUT
TYP
MAX
1
0.2 x
VOUT
UNITS
µA
V
1
µA
0.3
V
0.4
1.0
µA
0.3
0.4
V
0.4
V
1425 1500 1575
Ω
-1
1
µA
5.5
pF
24
40
pF
47
3.6
5
V
3.6
16
V
16
V
±6
A
±16
±8
kV
±15
Note 1: All devices are 100% tested at TA = +25°C. Limits over temperature are guaranteed by characterization and not production
tested.
Note 2: Dropout voltage is defined as VIN - VOUT when VOUT is 2% below the value of VOUT for VIN = VOUT + 1V.
Note 3: Specification is guaranteed to ±4σ limit.
_______________________________________________________________________________________ 3
Share Link: 