ISL43640IR 查看數據表（PDF） - Renesas Electronics
零件编号
产品描述 (功能)
比赛名单
ISL43640IR
Renesas Electronics
ISL43640IR Datasheet PDF : 13 Pages
| |||
ISL43640
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
Input Voltages
INH, NO, NC, ADD (Note 2) . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . 40mA
Operating Conditions
Temperature Range
ISL43640IX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
Thermal Information
Thermal Resistance (Typical)
JA (°C/W)
10 Ld MSOP Package (Note 3) . . . . . . . . . . . . . . . .
190
16 Ld QFN Package (Note 4). . . . . . . . . . . . . . . . . .
62
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Moisture Sensitivity (See Technical Brief TB363)
All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(MSOP - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, COM, ADD, or INH exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current
ratings.
3. JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
4. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
Electrical Specifications +5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
ON Resistance, RON
V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3.5V,
(See Figure 5)
RON Matching Between Channels,
RON
RON Flatness, RFLAT(ON)
V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3.5V, (Note 8)
V+ = 5.5V, ICOM = 1.0mA, VNO or VNC = 1.5V, 2.5V,
3.5V, (Note 9)
NO or NC OFF Leakage Current,
INO(OFF) or INC(OFF)
V+ = 5.5V, VCOM = 1V, 4.5V, VNO or VNC = 4.5V, 1V,
(Note 7)
COM OFF Leakage Current,
ICOM(OFF)
V+ = 5.5V, VCOM = 4.5V, 1V, VNO or VNC = 1V, 4.5V,
(Note 7)
COM ON Leakage Current,
ICOM(ON)
V = 5.5V, VCOM = 1V, 4.5V, or VNO or VNC = 1V, 4.5V,
or Floating, (Note 7)
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, VINH
Input Voltage Low, VINL
Input Current, IINH, IINL
DYNAMIC CHARACTERISTICS
Inhibit Turn-ON Time, tON
V+ = 5.5V, VIN = 0V or V+
V+ = 4.5V, VNO or VNC = 3V, RL = 300, CL = 35pF,
VIN = 0 to 3, (See Figure 1)
Inhibit Turn-OFF Time, tOFF
V+ = 4.5V, VNO or VNC = 3V, RL = 300, CL = 35pF,
VIN = 0 to 3, (See Figure 1)
Address Transition Time, tTRANS
V+ = 4.5V, VNO or VNC = 3V, RL = 300, CL = 35pF,
VIN = 0 to 3, (See Figure 1)
Break-Before-Make Time Delay, tD V+ = 5.5V, RL = 300, CL = 35pF, VNO = VNC = 3V, VIN
= 0 to 3, (See Figure 3)
TEMP
(°C)
Full
25
Full
25
Full
25
Full
25
Full
25
Full
25
Full
Full
Full
Full
25
Full
25
Full
25
Full
Full
(NOTE 6)
MIN
0
-
-
-
-
-
-
-1
-2.5
-1
-2.5
-1
-5
2.4
-
-0.5
-
-
-
-
-
-
5
TYP
-
115
-
1
-
12
13
-
-
-
-
-
-
1.4
1.3
-
60
-
30
-
61
-
16
(NOTE 6)
MAX UNITS
V+
V
125
150
3
5
13
18
1
nA
2.5
nA
1
nA
2.5
nA
1
nA
5
nA
-
V
0.8
V
0.5
µA
65
ns
80
ns
35
ns
40
ns
70
ns
85
ns
-
ns
FN6043 Rev 3.00
Jan 23, 2006
Page 3 of 13
Share Link: