HIP4081A 查看數據表（PDF） - Renesas Electronics

零件编号

产品描述 (功能)

比赛名单

HIP4081A

80V/2.5A Peak, High Frequency Full Bridge FET Driver

Renesas Electronics 

HIP4081A

Pin Descriptions

PIN

NUMBER

SYMBOL

DESCRIPTION

1

BHB B High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap

diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30A out of this pin to

maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.

2

BHI

B High-side Input. Logic level input that controls BHO driver (Pin 20). BLI (Pin 5) high level input overrides BHI high

level input to prevent half-bridge shoot-through, see Truth Table. DIS (Pin 3) high level input overrides BHI high level

input. The pin can be driven by signal levels of 0V to 15V (no greater than VDD).

3

DIS

DISable input. Logic level input that when taken high sets all four outputs low. DIS high overrides all other inputs.

When DIS is taken low the outputs are controlled by the other inputs. The pin can be driven by signal levels of 0V to

15V (no greater than VDD).

4

VSS

Chip negative supply, generally will be ground.

5

BLI

B Low-side Input. Logic level input that controls BLO driver (Pin 18). If BHI (Pin 2) is driven high or not connected

externally then BLI controls both BLO and BHO drivers, with dead time set by delay currents at HDEL and LDEL (Pin

8 and 9). DIS (Pin 3) high level input overrides BLI high level input. The pin can be driven by signal levels of 0V to 15V

(no greater than VDD).

6

ALI

A Low-side Input. Logic level input that controls ALO driver (Pin 13). If AHI (Pin 7) is driven high or not connected

externally then ALI controls both ALO and AHO drivers, with dead time set by delay currents at HDEL and LDEL (Pin

8 and 9). DIS (Pin 3) high level input overrides ALI high level input. The pin can be driven by signal levels of 0V to 15V

(no greater than VDD).

7

AHI

A High-side Input. Logic level input that controls AHO driver (Pin 11). ALI (Pin 6) high level input overrides AHI high

level input to prevent half-bridge shoot-through, see Truth Table. DIS (Pin 3) high level input overrides AHI high level

input. The pin can be driven by signal levels of 0V to 15V (no greater than VDD).

8

HDEL High-side turn-on DELay. Connect resistor from this pin to VSS to set timing current that defines the turn-on delay of

both high-side drivers. The low-side drivers turn-off with no adjustable delay, so the HDEL resistor guarantees no

shoot-through by delaying the turn-on of the high-side drivers. HDEL reference voltage is approximately 5.1V.

9

LDEL Low-side turn-on DELay. Connect resistor from this pin to VSS to set timing current that defines the turn-on delay of

both low-side drivers. The high-side drivers turn-off with no adjustable delay, so the LDEL resistor guarantees no

shoot-through by delaying the turn-on of the low-side drivers. LDEL reference voltage is approximately 5.1V.

10

AHB A High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap

diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30A out of this pin to

maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.

11

AHO A High-side Output. Connect to gate of A High-side power MOSFET.

12

AHS A High-side Source connection. Connect to source of A High-side power MOSFET. Connect negative side of

bootstrap capacitor to this pin.

13

ALO A Low-side Output. Connect to gate of A Low-side power MOSFET.

14

ALS

A Low-side Source connection. Connect to source of A Low-side power MOSFET.

15

VCC

Positive supply to gate drivers. Must be same potential as VDD (Pin 16). Connect to anodes of two bootstrap diodes.

16

VDD

Positive supply to lower gate drivers. Must be same potential as VCC (Pin 15). De-couple this pin to VSS (Pin 4).

17

BLS

B Low-side Source connection. Connect to source of B Low-side power MOSFET.

18

BLO B Low-side Output. Connect to gate of B Low-side power MOSFET.

19

BHS B High-side Source connection. Connect to source of B High-side power MOSFET. Connect negative side of

bootstrap capacitor to this pin.

20

BHO B High-side Output. Connect to gate of B High-side power MOSFET.

FN3659 Rev 8.00

September 15, 2015

Page 6 of 17

Share Link: