ISL8501 查看數據表（PDF） - Renesas Electronics

零件编号

产品描述 (功能)

比赛名单

ISL8501

Triple Output Controller with 1A Standard Buck PWM and Dual LDOs

Renesas Electronics 

ISL8501

charges the external soft-start capacitor. The voltage on SS

begins ramping linearly from ground until the voltage across

the soft-start capacitor reaches 3.0V. This linear ramp is

applied to the non-inverting input of the internal error

amplifier and overrides the nominal 0.6V reference. The

output voltage reaches its regulation value when the soft-

start capacitor voltage reaches 1.6V. Connect a capacitor

from SS pin to ground. This capacitor, along with an internal

30A current source sets the soft-start interval of the

converter, tSS.

CSSF = 50  tSSS

(EQ. 1)

Upon disable, SS pin voltage will discharge to zero voltage.

Power Good

PG_PWM is an open-drain output of a window comparator

that continuously monitors the buck regulator output voltage.

PG_PWM is actively held low when EN is low and during the

buck regulator soft-start period. After the soft-start period

terminates, PG_PWM becomes high impedance as long as

the output voltage is within ±10% of the nominal regulation

voltage set by FB_PWM. When VOUT drops 10% below or

rises 10% above the nominal regulation voltage, the

ISL8501 pulls PG_PWM low. Any fault condition forces

PG_PWM low until the fault condition is cleared by attempts

to soft-start. For logic level output voltages, connect an

external pull-up resistor between PG_PWM and VCC. A

100k resistor works well in most applications. Note that the

PG_PWM window detector is completely independent of the

undervoltage protection fault detectors and the state of

LDO1 and LDO2 outputs.

PG_LDO is an open drain pull-down NMOS output that will

sink 1mA at 0.3V max. PG_LDO monitors both LDO1 and

LDO2 output. It goes to the active low state if either LDO

output is below regulation by a value greater than 15%.

When the one of the LDO is disabled, the PG_LDO switch to

only monitor the active LDO output.

Output Voltage Selection

All three regulator output voltages can be programmed using

external resistor dividers that scale the voltage feedback

relative to the internal reference voltage. The scaled voltage

is fed back to the inverting input of the error amplifier. Refer

to Figure 3.

The output voltage programming resistor, R2, will depend on

the value chosen for the feedback resistor, R1, and the

desired output voltage, VOUT, of the regulator. See Equation 1.

The value for the feedback resistor is typically between 1k

and 10k.

R2 = V-----OR----U-1---T-----0–---.--06---.-V-6---V---

(EQ. 2)

If the output voltage desired is 0.6V, then R2 is left

unpopulated.

VOUT

R1

EA

R2

0.6V

REFERENCE

FIGURE 31. EXTERNAL RESISTOR DIVIDER

The buck output can be program as high as 20V. Proper

heatsinking must be provided to insure that the junction

temperature do not exceed +125°C.

When the output is set greater than 3.6V, it is recommended

to pre-load at least 1mA and make sure that the input rise

time is >> faster than the VOUT1 rise time. This allows the

BOOT capacitor adequate time to charge for proper

operation.

Protection Features

The ISL8501 limits current in all on-chip power devices to

limit on-chip power dissipation. Overcurrent limits on all three

regulators protect internal power devices from excessive

thermal damage. Undervoltage protection circuitry on the

buck regulator provides a second layer of protection for the

internal power device under high current conditions.

Buck Regulator Overcurrent Protection

During the PWM on-time, the current through the internal

switching MOSFET is sampled and scaled through an

internal pilot device. The sampled current is compared to a

nominal 2A overcurrent limit. If the sampled current exceeds

the overcurrent limit reference level, an internal overcurrent

fault counter is set to 1 and an internal flag is set. The

internal power MOSFET is immediately turned off and will

not be turned on again until the next switching cycle.

The protection circuitry continues to monitor the current and

turns off the internal MOSFET as described. If the over-

current condition persists for four sequential clock cycles,

the over-current fault counter overflows indicating an

overcurrent fault condition exists. The regulator is shut down

and power good goes low. If the overcurrent condition clears

prior to the counter reaching four consecutive cycles, the

internal flag and counter are reset.

The protection circuitry attempts to recover from the

overcurrent condition after waiting 4 soft-start cycles. The

internal overcurrent flag and counter are reset. A normal

soft-start cycle is attempted and normal operation continues

if the fault condition has cleared. If the overcurrent fault

counter overflows during soft-start, the converter shuts down

and this hiccup mode operation repeats.

FN6500 Rev 1.00

July 12, 2007

Page 14 of 19

Share Link: