74ALVT16823DL 查看數據表（PDF） - Philips Electronics
零件编号
产品描述 (功能)
比赛名单
74ALVT16823DL
Philips Electronics
74ALVT16823DL Datasheet PDF : 12 Pages
| |||
Philips Semiconductors
2.5V/3.3V 18-bit bus-interface D-type flip-flop
with reset and enable (3-State)
Product specification
74ALVT16823
DC ELECTRICAL CHARACTERISTICS (2.5V "0.2V RANGE)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Temp = -40°C to +85°C UNIT
MIN TYP1 MAX
VIK
Input clamp voltage
VOH
High-level output voltage
VOL
Low-level output voltage
VCC = 2.3V; IIK = –18mA
VCC = 2.3 to 3.6V; IOH = –100µA
VCC = 2.3V; IOH = –8mA
VCC = 2.3V; IOL = 100µA
VCC = 2.3V; IOL = 24mA
VCC = 2.3V; IOL = 8mA
–0.85 –1.2
V
VCC–0.2 VCC
V
1.8
2.5
0.07 0.2
0.3 0.5
V
0.4
VRST
II
IOFF
IHOLD
IEX
IPU/PD
Power-up output low voltage7
Input leakage current
Off current
Bus Hold current
D inputs6
Current into an output in the
High state when VO > VCC
Power up/down 3-State output
current3
VCC = 2.7V; IO = 1mA; VI = VCC or GND
VCC = 2.7V; VI = VCC or GND
VCC = 0 or 2.7V; VI = 5.5V
VCC = 3.6V; VI = VCC
VCC = 3.6V; VI = 0
VCC = 0V; VI or VO = 0 to 4.5V
VCC = 2.3V; VI = 0.7V
VCC = 2.3V; VI = 1.7V
Control pins
Data pins4
VO = 5.5V; VCC = 2.3V
VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC;
OE/OE = Don’t care
0.55
V
0.1
±1
0.1
10
µA
0.1
1
0.1
-5
0.1 ±100 µA
100
µA
–70
µA
10
125
µA
1
±100 µA
IOZH 3-State output High current
VCC = 2.7V; VO = 2.3V; VI = VIL or VIH
0.5
5
µA
IOZL
3-State output Low current
VCC = 2.7V; VO = 0.5V; VI = VIL or VIH
0.5
–5
µA
ICCH
VCC = 2.7V; Outputs High, VI = GND or VCC, IO = 0
0.04 0.1
ICCL
Quiescent supply current
VCC = 2.7V; Outputs Low, VI = GND or VCC, IO = 0
2.7 4.5 mA
ICCZ
VCC = 2.7V; Outputs Disabled; VI = GND or VCC, IO = 05
0.04 0.1
∆ICC
Additional supply current per
input pin2
VCC = 2.3V to 2.7V; One input at VCC–0.6V,
Other inputs at VCC or GND
0.04 0.4 mA
NOTES:
1. All typical values are at VCC = 2.5V and Tamb = 25°C.
2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND
3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 2.5V ± 0.2V a
transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.
4. Unused pins at VCC or GND.
5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground.
6. Not guaranteed.
7. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power.
AC CHARACTERISTICS (2.5V "0.2V RANGE)
GND = 0V, tR = tF = 2.5ns, CL = 50pF, RL = 500Ω , Tamb = –40°C to +85°C
SYMBOL
PARAMETER
WAVEFORM
fMAX
Maximum clock frequency
1
tPLH
Propagation delay
tPHL
nCP to nQx
1
tPHL
Propagation delay
nMR to nQx
2
tPZH
Output enable time
4
tPZL
to High and Low level
5
tPHZ
Output disable time
4
tPLZ
from High and Low level
5
NOTE:
1. All typical values are at VCC = 3.3 V and Tamb = 25°C
LIMITS
VCC = +2.5V±0.2V
MIN
TYP1
MAX
150
–
–
–
2.6
5.2
2.4
4.2
–
2.5
4.5
–
2.3
5.6
3.2
5.3
–
3.3
5.6
3.0
6.7
UNIT
MHz
ns
ns
ns
ns
1998 Jun 12
7
Share Link: