MCCF33095D 查看數據表（PDF） - Motorola => Freescale
零件编号
产品描述 (功能)
比赛名单
MCCF33095D Datasheet PDF : 12 Pages
| |||
MCCF33095 MC33095
MAXIMUM RATINGS (Notes 1 and 3)
Rating
Steady State VCC, VIGN, VSTA
VCC and VIGN Transient
Bump Shear Strength (Flip–Chip)
Thermal Characteristics (Thermal Resistance)
Junction–to–Substrate (Flip–Chip)
Junction–to–Ambient (SO–14)
Junction Temperature
Flip–Chip
SO–14
Operating Ambient Temperature Range
Flip–Chip
SO–14
Symbol
–
–
–
RθJS
RθJA
TJ
TA
Value
Unit
9.0 to 24
V
80
V
8.0
Grams/Bump
°C/W
29
145
°C
170
150
°C
– 40 to +170
– 40 to +125
ELECTRICAL CHARACTERISTICS (Limit values are given for – 40°C ≤ TA ≤ 150°C (Flip–Chip), –40°C ≤ TA ≤ 125°C
(SO–14) and typical values represent approximate mean value at TA = 25°C. Oscillator, Roll–Off, Ground, Short Circuit = 0 V,
and 12 V ≤ VCC, Sense, Stator, Ignition ≤ 16 V, unless otherwise specified.)
Characteristic
Symbol Min Typ Max Unit
SUPPLY (VCC)
Supply Current
Disabled (Ignition = 0.5 V, Stator = 5.0 V)
Enabled (VCC, Sense = 17 V, Ignition = 1.4 V)
Darlington Drive Overvoltage
Disable Threshold (VCC, Ignition, Short Circuit = 19 V to 29 V Ramp, Stator = 10 V)
Hysteresis (VCC, Stator, Ignition, Short Circuit = 29 V to 19 V Ramp)
Lamp Overvoltage
Disable Threshold (VCC, Stator, Ignition, Short Circuit = 19 V to 29 V Ramp)
Hysteresis
ICC
– 50 0.2 300 µA
0
3.9
25
mA
V
VCODD 19
VCODDH –
26 28.5
4.2
–
V
VCOL
19 22.3 29.5
VCOLH
–
0.3
–
SENSE
Sense Current (Oscillator = 2.0 V)
Calibration Voltage (50% Duty Cycle) (Note 5)
Lamp Comparator Detect Threshold
Proportional Control Range
Lamp Comparator Reset Threshold
Lamp Hysteresis
STATOR
Propagation Delay (Lamp–to–High, Stator = 15 V to 6.0 V)
Reset Threshold Voltage (Lamp–to–Low, Stator = 5.0 V to 11 V)
Input Current (Sense = 18 V, Oscillator = 2.0 V)
LAMP
Saturation Voltage (Lamp = 14 mA)
Leakage Current (Sense = 1.0 V, Lamp = 2.5 V)
Saturation Voltage (VCC, Sense, Stator, Ignition = 30 V, Lamp = 20 mA)
ISNS
–10 0.6
10
µA
VR
12.25 14.6 17.5 V
VSCD
–
16.3
–
V
MV
50 187.4 350 mV
VHV
15.4 15.9 16.4
V
VHYS
20 416.6 600 mV
tSTA
VIH
ISTA
6.0 59.4 600 ms
6.0 8.8
11
V
–10 1.5
10
µA
VOLL
0 111.8 350 mV
IOHL
– 50 0.8
50
µA
VOOLL
0 147.4 350 mV
NOTES: 1. VCC applied through a 250 Ω resistor.
2. Sense input applied through a 100 kΩ and 50 kΩ resistor divider to generate one–third Vbat.
3. Stator and Ignition inputs applied through a 20 kΩ resistor.
4. Short Circuit input applied through a 30 kΩ resistor.
5. Oscillator pin connected in series with 0.022 µF capacitor to ground.
2
MOTOROLA ANALOG IC DEVICE DATA
Share Link: 