ISL8560 查看數據表（PDF） - Renesas Electronics

零件编号

产品描述 (功能)

比赛名单

ISL8560

DC/DC Power Switching Regulator

Renesas Electronics 

ISL8560

Typical Performance Curves (Continued)

LX = 10V/DIV

VOUT = 2V/DIV

IL = 2A/DIV

PGOOD = 5V/DIV

FIGURE 28. OUTPUT SHORT CIRCUIT

Applications Information

Product Description

The ISL8560 is a non-synchronous, integrated FET 2A step

down regulator which operates from an unregulated input of 9V

to 60V. The output voltage is user-adjustable with a pair of

external resistors. Frequency of operation is adjustable from

100kHz to 600kHz set by RTCT. An external signal with higher

frequency can be injected to SYNCH to synchronize the

controller.

The buck controller drives an internal N-Channel MOSFET and

requires an external diode to deliver load current up to 2A. A

Schottky diode is recommended for improved efficiency and

performance over a standard diode. The converter output is

regulated down to 1.21V from an input source.

The PWM control loop uses a single output voltage loop with

input voltage feed forward which simplifies feedback loop

compensation and rejects input voltage variation. External

feedback loop compensation allows flexibility in output filter

component selection.

The buck regulator is equipped with a lossless current limit

scheme. The current limit in the buck regulator is achieved by

monitoring the drain-to-source current of the internal switching

power MOSFET. The current limit threshold is internally set at

4.5A peak. Additional features include programable soft-start to

support proper start-up of wide output capacitance range.

Start-Up and Shut-Down

When the EN pin is connected to a logic high, the ISL8560 is in

the shut-down mode. All the control circuitry and both

MOSFETs are off, and VOUT falls to zero. In this mode, the

total input current is less than 110µA.

When the EN pin is tied to GND, and VIN reaches

approximately 9V, the regulator begins to switch. The output

voltage is gradually increased to ensure proper soft-start

operation.

When the EN reaches logic LOW, the regulator repeats the

start-up procedure, including the soft-start function. Connect a

capacitor from SS pin to ground. This capacitor, along with an

internal 10µA current source sets the soft-start interval of the

converter, tSS.

CSSF  8.3  tSSs

(EQ. 1)

Operating Frequency

The ISL8560 can operate at switching frequencies from

100kHz to 600kHz. A resistor tied from the RTCT pin to VIN

and a capacitor from RTCT to GND are used to program the

switching frequency through Equation 2.

C1nF

=

R----6---.-k-2---5-----





-f-O-----S--1--C--0---0-k--0--H-----z----

–

0.3

(EQ. 2)

Caution: When the ISL8560 is in disabled state, the voltage

across RTCT pin will reach VIN voltage. Make sure that the

voltage rating of the RTCT capacitor is rated as high as the

input voltage.

Output Voltage Selection

The output voltage of the regulator can be programmed via an

external resistor divider that is used to scale the output voltage

relative to the internal reference voltage and feed it back to the

inverting input of the error amplifier. Refer to Figure 30.

The output voltage programming resistor, R3, will depend on

the value chosen for the feedback resistor and the desired

output voltage of the regulator. The value for the feedback

resistor is typically between 1k and 10k.

R3 = -V----RO----U2----T-----–1----.-12---.-1-2---V1----V--

(EQ. 3)

If the output voltage desired is 1.21V, then R3 is left

unpopulated.

FN9244 Rev 7.00

September 19, 2008

Page 11 of 17

Share Link: